Paso 3: El código
#include "Wire.h" #include "RTClib.h" #include "FastLED.h" byte LEDs[][2]={ // Array to define the Charlieplexed LEDs {3,4}, {5,6}, {7,8}, {9,10}, {4,3}, // 5 {6,5}, {8,7}, {10,9}, {3,5}, {4,6}, //10 {7,9}, {8,10}, {5,3}, {6,4}, {9,7}, //15 {10,8}, {3,6}, {4,7}, {5,8}, {9,11}, //20 {6,3}, {7,4}, {8,5}, {11,9}, {3,7}, //25 {4,8}, {5,9}, {6,10}, {4,9}, {8,4}, //30 {9,5}, {10,6}, {3,8}, {7,3}, {5,10}, //35 {6,11}, {8,3}, {9,4}, {10,5}, {11,6}, //40 {3,9}, {4,10}, {5,11}, {9,3}, {10,4}, //45 {11,5}, {3,10}, {4,11}, {10,3}, {11,3}, //50 {11,4}, {4,5}, {6,7}, {8,9}, {10,11}, //55 {5,4}, {7,6}, {9,8}, {5,7}, {6,8} //60 }; #define NUM_LEDS 60 #define DATA_PIN 12 CRGB leds[NUM_LEDS]; byte lastmin; RTC_DS1307 rtc; void setup() { // put your setup code here, to run once: AllOff(); #ifdef AVR Wire.begin(); #else Wire1.begin(); // Shield I2C pins connect to alt I2C bus on Arduino Due #endif rtc.begin(); lastmin=0; LEDS.setBrightness(128); FastLED.addLeds<WS2812B, DATA_PIN, GRB>(leds, NUM_LEDS); //effects(); //Serial.begin(57600); } void loop() { // put your main code here, to run repeatedly: DateTime now = rtc.now(); // Serial.print(now.hour(), DEC); if(( now.second() == 0)){ effects(); } if(now.minute() != lastmin){ for(int i=0; i<now.minute();i++) leds[i] = CRGB::Purple; leds[((now.hour())%12)*5] = CRGB::Red; FastLED.show(); } LEDOn(now.second()); delay(900); AllOff(); //leds[((now.hour())%12)*5] = CRGB::Black; //leds[now.minute()] = CRGB::Black; //FastLED.show(); delay(100); //} } void LEDOn(byte n){ AllOff(); pinMode(LEDs[n][0],OUTPUT); pinMode(LEDs[n][1],OUTPUT); digitalWrite(LEDs[n][0],HIGH); digitalWrite(LEDs[n][1],LOW); } void AllOff(){ for(int i=3;i<=11;i++){ pinMode(i,INPUT); } } const int colorWheelAngle = 360 / NUM_LEDS; void effects(){ uint8_t color[3]; for (int i = 0; i < 360; i++) { for (int j = 0; j < NUM_LEDS; j++) { getRGB((i + (j * colorWheelAngle)) % 360, 255, 150, color); leds[j]=CRGB(color[0], color[1], color[2]); } FastLED.show(); delay(1); } for (int i = 0; i < NUM_LEDS; i++) { leds[i] = CRGB::Black; } FastLED.show(); } // Gamma values used to convert HSV to RGB PROGMEM const byte dim_curve[] = { 0, 1, 1, 2, 2, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 6, 6, 6, 6, 6, 6, 6, 6, 7, 7, 7, 7, 7, 7, 7, 8, 8, 8, 8, 8, 8, 9, 9, 9, 9, 9, 9, 10, 10, 10, 10, 10, 11, 11, 11, 11, 11, 12, 12, 12, 12, 12, 13, 13, 13, 13, 14, 14, 14, 14, 15, 15, 15, 16, 16, 16, 16, 17, 17, 17, 18, 18, 18, 19, 19, 19, 20, 20, 20, 21, 21, 22, 22, 22, 23, 23, 24, 24, 25, 25, 25, 26, 26, 27, 27, 28, 28, 29, 29, 30, 30, 31, 32, 32, 33, 33, 34, 35, 35, 36, 36, 37, 38, 38, 39, 40, 40, 41, 42, 43, 43, 44, 45, 46, 47, 48, 48, 49, 50, 51, 52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 68, 69, 70, 71, 73, 74, 75, 76, 78, 79, 81, 82, 83, 85, 86, 88, 90, 91, 93, 94, 96, 98, 99, 101, 103, 105, 107, 109, 110, 112, 114, 116, 118, 121, 123, 125, 127, 129, 132, 134, 136, 139, 141, 144, 146, 149, 151, 154, 157, 159, 162, 165, 168, 171, 174, 177, 180, 183, 186, 190, 193, 196, 200, 203, 207, 211, 214, 218, 222, 226, 230, 234, 238, 242, 248, 255, }; /* * Code taken from <a href="http://www.kasperkamperman.com/blog/arduino/arduino-programming-hsb-to-rgb/" rel="nofollow"> http://www.kasperkamperman.com/blog/arduino/ardui...</a> * hue ranges from 0 to 360 * sat is from 0 to 255 * val is from 0 to 255 */ void getRGB(int hue, uint8_t sat, uint8_t val, uint8_t colors[3]) { /* convert hue, saturation and brightness ( HSB/HSV ) to RGB The dim_curve is used only on brightness/value and on saturation (inverted). This looks the most natural. */ val = pgm_read_byte(&dim_curve[val]); sat = 255 - pgm_read_byte(dim_curve[255-sat]); int r; int g; int b; int base; if (sat == 0) { // Acromatic color (gray). Hue doesn't mind. colors[0]=val; colors[1]=val; colors[2]=val; } else { base = ((255 - sat) * val)>>8; switch(hue/60) { case 0: r = val; g = (((val-base)*hue)/60)+base; b = base; break; case 1: r = (((val-base)*(60-(hue%60)))/60)+base; g = val; b = base; break; case 2: r = base; g = val; b = (((val-base)*(hue%60))/60)+base; break; case 3: r = base; g = (((val-base)*(60-(hue%60)))/60)+base; b = val; break; case 4: r = (((val-base)*(hue%60))/60)+base; g = base; b = val; break; case 5: r = val; g = base; b = (((val-base)*(60-(hue%60)))/60)+base; break; } colors[0]=(uint8_t) r; colors[1]=(uint8_t) g; colors[2]=(uint8_t) b; } }
